|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
Stripline Mounting Non-reflective Terminations HT Series sFeatures 1.High Performance These super wide bandwidth/ultra high matching non-reflective termination use Hirose Electric original high frequency matching technology. HT-30-1 HT-50-1 HT-10-2 HT-20-3 2.Equipped with Tabs Termination are equipped with tabs to permit direct mounting to flat circuits. HT-1-3 HT-1-2 HT-1-1 HT-025-1 HT-05-2 HT-025-2 3.Housing functions as a radiator to permit small size and high-density mounting. sProduct Specifications Ratings Rated frequency range (Note) Characteristic impedance Maximum Input Power (Note) DC to 15.0 GHz 50 ohms 0.25 to 50 W Operating temperature range Operating relative humidity -10c to +60c 95% Max. NOTE: The frequency range and the maximum input power will differ depending on the products. HT-025-1, HT-025-2, HT-05-2, HT-1-1, HT-1-2, HT-1-3, HT-10-2, HT-20-3, and HT-50-1 Item 1.Vibration No electrical discontinuity of 1 s or more No damage, cracks, or parts dislocation 2.Shock 3.Temperature cycle No damage, cracks, or parts dislocation Standard Conditions Frequency of 10 to 2000 Hz, overall amplitude of 1.52 mm, acceleration of 98 m/s2 for 2 hours in each of 3 directions Acceleration of 490 m/s2, sine half-wave waveform, 3 cycles in each of the 3 axis Temperature: -55c +5c to +35c +85c +5c to +35c Time: 30 15 max. 30 15 max. (Minutes) 200 cycles qThe test method conforms to MIL-STD-202. HT-30-1 Item 1.Vibration No electrical discontinuity of 1 s or more No damage, cracks, or parts dislocation 2.Shock 3.Temperature cycle No damage, cracks, or parts dislocation Standard Conditions Frequency of 10 to 2000 Hz, overall amplitude of 1.52 mm, acceleration of 98 m/s2 for 2 hours in each of 3 directions Acceleration of 294 m/s2, sine half-wave waveform, 3 cycles in each of the 3 axis Temperature: -55c +5c to +35c +120c +5c to +35c Time: 30 15 max. 30 15 max. (Minutes) 200 cycles qThe test method conforms to MIL-STD-202. sMaterials HT-025-1, HT-025-2, and HT-05-2 Part Tabs Resistor Material Copper Metal film Finish Solder plating ---------- HT-1-1, HT-1-2, and HT-1-3 Part Plate Tabs Resistor Material Aluminum Copper Metal film Finish Nickel plating Solder plating ---------- HT-30-1 Part Plate Retaining plate Tabs Resistor Material Aluminum Phosphor bronze Copper Metal film Finish Conductive alumite Nickel plating Tin plating ---------- HT-10-2, HT-20-3, and HT-50-1 Part Plate Tabs Resistor Material Copper Copper Metal film Finish Nickel plating Silver plating ---------- 72 sOrdering Information HT - 025 - 1 1 2 3 1 Series Name: HT Series 2 Power (Example)0.25:0.25W 1:1W 3 Suffix sSpecifications Part Number HT-025-1 HT-025-2 HT-05-2 HT-1-1 HT-1-2 HT-1-3 HT-10-2 ! Frequnency Range (GHz) DC-8 DC-8 DC-1 DC-8 DC-6 DC-15 DC-1 DC-5 V.S.W.R. (MAX) 1.30 1.30 1.20 1.30 1.20 1.15(DC-4GHz) 1.25(4-8GHz) 1.45(8-12.4GHz) 1.55(12.4-15GHz) 1.20 1.25 Impedance (Ohms) 50 50 50 50 50 50 50 50 Power (W) 1/4 1/4 1/2 1 10 20 30 50 Heat Sink Temperature at Maximum Load (c Max) +65 +65 +65 +65 +65 +65 +65 +65 Heat Resistance (c/ W) 50 50 150 50 9 3.8 3 1.6 Weight (g) 0.1 0.1 0.3 0.3 0.3 0.6 3 1.5 HT-20-3 HT-30-1 ! HT-50-1 ! CAUTION: Beryllia is used in this product. Please follow associated laws when disposing. sTypical Data HT-1-3 HT-10-2 HT-20-3 HT-50-1 73 sExternal Dimensions HT-025-1 HT-025-2 HT-05-2 PCB Mounting Pattern PCB Mounting Pattern HT-1-1 * HT-1-2 * HT-1-3 HT-30-1 Part Number HT-1-1 HT-1-2 HT-1-3 A 13 13 16 B 8 8 12 C 2.5 2.5 2 D 1.4 1.4 1.4 E 5.4 5.4 5.4 F 1.45 1.15 1.45 G 1.49 1.19 1.49 PCB Mounting Pattern PCB Mounting Pattern Part Number A 1.65 2 B 1.7 2.05 HT-10-2 HT-20-3 HT-10-2 HT-20-3 HT-50-1 74 sMounting Method qDo not leave a space between the terminator and the microstrip board. qMake the terminator tab height from the housing and the thickness of the microstrip board the same amount. qNote: The HT-025-1 type is attached with high temperature solder (having a melting point of 280c). The soldering temperature to the microstrip board must be less than this. HT-025-1 qMounting is performed by soldering over the microstrip line pattern. qThe mounting should be completed by soldering within 5 seconds using Sn-Pb type eutectic solder containing 2 to 5% Ag with a soldering iron adjusted to about 260c. qThe resoldering of an item that has already been soldered once and then removed is not effective since solder cracks will develop at the electrode portion. HT-05-2 qDo not leave a space between the terminator and the microstrip board. qDo not leave a space between the the microstrip board. qNote: The HT-1-1, HT-1-2, HT-1-3, HT-10-2, HT-203, and HT-50-1 tabs are attached with high temperature solder (having a melting point of 280c). The soldering temperature to the microstrip board must be less than this. Note: Although the high frequency characteristics will deteriorate somewhat, please attach with some slack in the tabs in order to raise the thermal reliability. HT-1-1, HT-1-2, HT-1-3, HT-10-2, HT-20-3, HT-30-1, HT-50-1 75 Terminations for the Division Part of a Wilkinson Divider (100 ohms Type) HT Series sFeatures 1.High Performance These wide bandwidth/ultra high matching nonreflective termination use Hirose Electric original high frequency matching technology. 2.Equipped with Tabs Termination are equipped with tabs to permit direct mounting to Wilkinson type flat circuits. 3.High Power and Small Size Beryllia is used for the material of the resistance element to enable the termination to be of small size and used with high power. HT-20-3(100) sProduct Specifications Ratings Rated frequency range Characteristic impedance Maximum Input Power Resistance value DC to 8.0 GHz 100 ohms 20W 1002 ohms Standard Heat sink temperature at maximum output Operating temperature range Operating relative humidity Weight Conditions Frequency of 10 to 2000 Hz, overall amplitude of 1.52 mm, acceleration of 98 m/s2 for 2 hours in each of 3 directions Acceleration of 490 m/s2, sine half-wave waveform, 3 cycles in each of the 3 axis Temperature: -55c +5c to +35c +120c +5c to +35c Time: 30 15 max. 30 15 max. (Minutes) 200 cycles +65cMax. 10cto +65c 95% Max. 0.4 g Item 1.Vibration No electrical discontinuity of 1 s or more No damage, cracks, or parts dislocation 2.Shock 3.Temperature cycle No damage, cracks, or parts dislocation sMaterial Part Plate Tabs Resistor Material Copper Copper Metal film Finish Nickel plating Silver plating ---------- sExternal Dimensions ! CAUTION: Beryllia is used in this product. Please follow associated laws when disposing. 76 |
Price & Availability of HT-50-1 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |